Allpro ScanX-12 DVM Instrukcja Obsługi Strona 1

Instruction ManualPart Numbers: High Resolution Unit B7350-214SHigh Contrast Unit B7350-550G

10COMPUTER SYSTEM REQUIREMENTSIMPORTANT: To operate the ScanX, it must be connected to a compliant Computer System, and the computer mu

11COMPUTER SYSTEM REQUIREMENTSCONTROLS & INDICATORSALLPROIMAGINGREADY ERASERFLASHINGOFFALLPROIMAGINGREADY ERASERFLASHINGOFFREADY SwitchFLASHING OF

12TECHNICAL DATAElectrical Requirements:Supply Voltage: 100 to 240VAC +/- 10%, 50/60 Hz Supply Current: 1.2 A MaximumLine Cord: North American styl

13The ScanX may be located almost anywhere in the office. Follow these guidelines for optimum performance: Lighting conditions: Set up the scanner i

14SYSTEM SETUPNote: Authorized Imaging Software supplied by the dealer or other company, must be installed on the computer in order to operate the Sc

15Figure 1. Typical ScanX InstallationPower SupplyComputer Connector CablePress HERE toturn ON or OFFGreen LED IndicatorPower SupplyLine CordMain

16Prior to performing the imaging procedure provided on the following pages, the user must be familiar with the care, handling and preparation of the

17PLATE CARE & PREPARATIONIMPORTANT: PSPs must always be erased prior to use.Note: Use PSPs within 24 hours of last erasure. Repeat erasing proc

18IMAGING PROCEDURES1. Orient the cassette so that the Tube side is facing down and the hinge is away from you. 2. Open the cassette and grasp

19IMAGING PROCEDURESScanning and Erasing Plates (continued)5. At this point, all four Scanner Track indicators will turn yellow, indicating the PSP h

2FOREWORDAir Techniques and its ALLPRO Imaging division have prepared this document as a guide to the proper use of the ScanX® 12 Digital Imaging Sys

20MAINTENANCE Maintenance ProceduresThe ScanX is designed for many years of trouble-free operation. Maintenance as described herein is minimal.IMPORTA

21Like all precision products, the ScanX requires a certain amount of care on a regularly scheduled basis. A well-organized maintenance p

22TROUBLESHOOTINGTrouble Possible Cause Corrective Action1. No power/No green light on membrane switch• Not plugged in.• No power at Mains Outlet•

23TROUBLESHOOTINGTrouble Possible Cause Corrective Action6. Image is too dark.• PSP has been overexposed • Use imaging software to adjust bright

24The following lists the ordering number and description for accessory components available to maintain the ScanX to meet your professional needs. Co

25NOTES

26NOTES

27NOTES

© Copyright Air Techniques, Inc. 2008P/N B7319 Rev. BAir Techniques and ALLPRO Imaging are leading manufacturers of fine dental, medical and veterinar

3CONGRATULATIONSWARRANTYQuickly and easily register your new ScanX on-line. Just have your product model and serial numbers available. Then

4SAFETY NOTICEThis equipment has been designed to minimize exposure of personnel to haz-ards. While the ScanX is designed for safe operation, cert

5SAFETY NOTICEUse of Accessory Equipment.The use of ACCESSORY equipment not complying with the equivalent safety requirements of this equipm

6Knowledge of Warnings and Cautions.Users must exercise every precaution to ensure personnel safety, and be familiar with the warnings and cautions pr

7General Notes. All instructions in this manual form an integral part of the unit. They must be kept close to the unit and in readiness whe

8IMPORTANT INFORMATIONCorrect Usage Operation of the ScanX may only be carried out by suitably qualified personnel. The ScanX is only to be used i

9UNPACKING & INSPECTIONUnpackingThe ScanX is shipped in a very special shipping case covered by a double-wall corrugated over-packaging. The case